Vane Padlock
Please note that the key is inserted in the direction of the key: the key handle must be vertical and the key on the key handle (the key is correctly inserted in the direction mark) can be inserted into the keyhole at the top. After confirming that the key has been fully inserted, turn the key clockwise to unlock it. Do not open the key in the end of the key to unlock the key, resulting in the key card stuck in the lock cylinder can not pull out or twist the key failure. The key in the rotation process is unable to pull out, only counterclockwise turn the key in the end locked, the key to pull out.
As the cylinder is used in the non-leaf structure, vane padlock, such as subject to a strong vibration, the impact of the blade in the 90 degree rotation within the free rotation, resulting in the key can not be inserted, so the safe, cabinet factory lock Holes are inserted with a key similar to the plastic rod, to prevent the free rotation of the blade. Please keep this plastic rod, move, transport safe, cabinet or long-term without a safe, cabinet, the plastic rod into the keyhole, both to prevent the free rotation of the blade can prevent foreign matter into the keyhole, do both.
composition
Which is mainly composed of a locking sleeve, a small pressing spring, a blade, a lock cylinder, a key and a flexible retaining ring, characterized in that the inner side of the locking sleeve has a wide groove, and the other side of the wide groove The two narrow corners are symmetrical with the radial centerline of the wide slot, and the two adjacent sides of the two narrow slots are parallel to the centerline and the other two edges are 2 degrees to 10 degrees Of the anti-angle, in the lock cylinder inside the 4-8 leaves of the groove, in each leaf slot, can be symmetrical flat two leaves, each leaf on the side of the side of 7-10 degrees of anti-angle, in each A small side of the blade on the side of the shoulder mounted a small compression spring, the lock cylinder into the lock sleeve, the end of the cylinder end of the round table with the end of the groove with the groove, the elastic ring into the front end of the lock cylinder , The lock is equipped with a lock lock in the car door lock hole, the front end of the lock cylinder and the car door switch connector fixed, the key made of two pieces of metal plate, each piece of metal plate welding or riveting one, In each piece of metal plate on both sides of the tooth flower, a key to form four rows of teeth, diagonal two rows of teeth the same.
Please note that the key is inserted in the direction of the key: the key handle must be vertical and the key on the key handle (the key is correctly inserted in the direction mark) can be inserted into the keyhole at the top. After confirming that the key has been fully inserted, turn the key clockwise to unlock it. Do not open the key in the end of the key to unlock the key, resulting in the key card stuck in the lock cylinder can not pull out or twist the key failure. The key in the rotation process is unable to pull out, only counterclockwise turn the key in the end locked, the key to pull out.
composition
Which is mainly composed of a locking sleeve, a small pressing spring, a blade, a lock cylinder, a key and a flexible retaining ring, characterized in that the inner side of the locking sleeve has a wide groove, and the other side of the wide groove The two narrow corners are symmetrical with the radial centerline of the wide slot, and the two adjacent sides of the two narrow slots are parallel to the centerline and the other two edges are 2 degrees to 10 degrees Of the anti-angle, in the lock cylinder inside the 4-8 leaves of the groove, in each leaf slot, can be symmetrical flat two leaves, each leaf on the side of the side of 7-10 degrees of anti-angle, in each A small side of the blade on the side of the shoulder mounted a small compression spring, the lock cylinder into the lock sleeve, the end of the cylinder end of the round table with the end of the groove with the groove, the elastic ring into the front end of the lock cylinder , The lock is equipped with a lock lock in the car door lock hole, the front end of the lock cylinder and the car door switch connector fixed, the key made of two pieces of metal plate, each piece of metal plate welding or riveting one, In each piece of metal plate on both sides of the tooth flower, a key to form four rows of teeth, diagonal two rows of teeth the same.
Comments
Post a Comment